Metalworking & Cutting Tools

Tungsten Carbide for Metalworking and Cutting Tools

Cutting tools need carbide that holds a sharp edge without chipping. MOSCARB supplies solid and coolant-hole carbide rods for drills, end mills and reamers, grades for gear cutting tool blanks, and inserts for plate beveling, chamfering and milling, in fine and ultrafine grain grades.

Wear challenge
Cutting Wear
Wear challenge
Edge Chipping
Wear challenge
High Contact Stress
Wear challenge
Dimensional Accuracy
Carbide end mill cutting metal

Industry Overview

Metalworking & Cutting Tools Overview

Solid carbide drills, end mills, reamers and gear hobs are ground from carbide blanks, and the blank decides how sharp the edge can be ground and how long it holds. Fine and ultrafine grain grades give the hardness and edge strength needed to machine steel, stainless steel, heat-resistant alloys and hardened materials.

MOSCARB supplies carbide rods with and without coolant holes, rods for PCB drills, grades for gear cutting tool blanks, and inserts for plate beveling, chamfering and milling machines.

Typical Applications

Metalworking & Cutting Tools Applications

01

Solid Carbide Drills

Rods with straight or helical coolant holes for drills with through-tool cooling.

02

End Mills and Reamers

Solid rods as blanks for end mills, reamers and taps.

03

Gear Cutting Tools

Blanks for gear hobs and gear cutting tools, including hard gear hobbing.

04

Plate Beveling and Milling

Inserts for beveling and chamfering machines, and brazed milling inserts.

Operating Conditions

Operating Conditions & Wear Challenges

Operating conditions

  • Cutting wear at the edge
  • Edge chipping
  • High contact stress
  • Dimensional accuracy requirements

Cutting Wear

The edge wears as it shears the workpiece; higher hardness and finer grain slow the wear.

Edge Chipping

Interrupted cuts and vibration chip the edge; a tougher grade or edge preparation is needed.

High Contact Stress

Hard workpieces concentrate high stress on the small contact area at the edge.

Dimensional Accuracy

Tool blanks must hold diameter and straightness so the tool can be ground accurately.

Carbide Solutions

Recommended Carbide Components

Tungsten carbide components we make for Metalworking & Cutting Tools.

Carbide Rods

Solid rods (metric) and rods with straight or helical coolant holes.

Rods for PCB Drills

Ultrafine-grain rods for PCB micro drills.

Gear Cutting Tool Blanks

Grades for gear hob blanks and gear cutting tools.

Beveling and Chamfering Inserts

Inserts for plate beveling and steel plate chamfering machines.

Milling Inserts

Brazed carbide milling inserts.

Custom Tool Blanks

Non-standard rods and blanks to your drawing.

Product categories

Material & Grade Selection

Carbide Grades for Metalworking & Cutting Tools

Compare all grades →

For rods, MU20 (sub-fine grain) suits drills and end mills for medium-speed machining of steel, aluminium alloys, heat-resistant alloys and cast iron; MU25UF is an ultrafine grade for milling stainless steel, titanium alloys and hardened materials at HRC 50–58; MU092 and MU10UF are ultrafine grades for precision finishing of hardened materials. For gear cutting tools, MS09U, MS12UF and MS10ST are chosen by the hardness of the gears being cut.

Tungsten carbide grades for Metalworking & Cutting Tools with typical properties
GradeISOCo (%)Grain Size (μm)Density (g/cm³)Hardness (HRA)TRS (N/mm²)Application
MU20K20-K40100.714.4591.83800Sub-fine-grain tungsten carbide rod grade for manufacturing solid carbide drills and end mills.
MU092K05-K1090.214.44944100Ultrafine-grain tungsten carbide rod grade for precision finishing of hardened materials above HRC 58.
MU25UFK20-K40120.414.192.64200Ultrafine tungsten carbide rod grade for milling stainless steel, non-ferrous metals, titanium alloys, high-temperature alloys and hardened materials at HRC 50–58.
MU10UFK05-K1060.414.8943800Ultrafine tungsten carbide rod grade for precision finishing of hardened materials and composites, including high-speed drill bits and engraving tools.
MS09U—90.414.5593.54000Ultrafine-grain cemented carbide grade combining sharp cutting edges with high wear resistance.
MS12UF—120.414.1292.54000Ultrafine-grain cemented carbide grade with excellent cutting-edge sharpness and wear resistance.
MS10ST—100.6–0.814.4591.73800Submicron-grain cemented carbide grade offering sharp cutting edges and resistance to edge chipping.

Technical FAQ

Metalworking & Cutting Tools: Technical FAQ

Which carbide grade should I use for end mills?

MU20 suits drills and end mills for medium-speed machining of steel, aluminium alloys, heat-resistant alloys and cast iron. For stainless steel, titanium alloys and hardened materials at HRC 50–58, MU25UF is used, and MU092 for precision finishing above HRC 58.

Which grade is used for gear hob blanks?

MS09U for hard gear hobbing of gears above HRC 60, MS12UF for gears up to HRC 55, and MS10ST, with its resistance to edge chipping, for gears up to HRC 35.

Do you supply rods with coolant holes?

Yes: rods with a straight central hole, two straight holes, two straight holes with a reduced bolt circle, and two or three helical holes.

What should I send for a quotation?

Rod diameter and length, coolant hole layout, tolerance, the grade or workpiece material, and the quantity.

Request a Quote

Send Your Drawing and Operating Conditions

Our engineers review the drawing and the application, recommend a grade and reply with questions or a quotation.

For a faster quotation, include:

  • Drawing (PDF) or main dimensions
  • Operating conditions: media, loads, temperature
  • How the current part wears or fails
  • Quantity and delivery schedule

Inquiry about: Metalworking & Cutting Tools

Files are used only to process your inquiry. Do not include confidential data unless you agree to share it with MOSCARB. Privacy policy