Dies, Molds & Metal Forming

Tungsten Carbide Dies and Metal Forming Applications

Forming dies must hold their shape under high compressive load, cycle after cycle. MOSCARB makes tungsten carbide wire drawing, cold heading, punching, stamping and extrusion dies, with grades matched to the die opening, the workpiece material and the forming method, from cold heading to hot forging.

Wear challenge
Compressive Load
Wear challenge
Repeated Cycles
Wear challenge
Friction and Abrasive Wear
Wear challenge
Dimensional Stability
Progressive stamping die for metal forming

Industry Overview

Dies, Molds & Metal Forming Overview

In drawing, heading, stamping and extrusion, the die shapes the workpiece under high pressure, cycle after cycle. Wear changes the size of every part produced, and a crack ends the life of the die. Tungsten carbide is used for its high hardness and compressive strength.

MOSCARB supplies wire drawing dies, cold heading dies, punching and stamping dies and extrusion dies, and makes non-standard dies to customer drawings. For heading and forming, the grade is matched to the die opening and to the material being formed.

Typical Applications

Dies, Molds & Metal Forming Applications

01

Wire Drawing

Dies for drawing wire down to size.

02

Cold Heading of Fasteners

Dies for heading screws, bolts and other fasteners, including stainless steel screws.

03

Punching and Stamping

Dies for punching and stamping, including battery case forming dies.

04

Extrusion and Forging

Extrusion dies, and grades for warm and hot forging dies.

Operating Conditions

Operating Conditions & Wear Challenges

Operating conditions

  • High compressive loads
  • Repeated forming cycles
  • Friction and abrasive wear
  • Dimensional stability

Compressive Load

The forming pressure is carried by the die bore; the grade must resist cracking under load.

Repeated Cycles

Fatigue from each forming cycle can start cracks at corners and transitions.

Friction and Abrasive Wear

The workpiece slides along the die surface and wears the working profile.

Dimensional Stability

Die wear changes the size of every part, so wear resistance governs part tolerance over the life of the die.

Carbide Solutions

Recommended Carbide Components

Tungsten carbide components we make for Dies, Molds & Metal Forming.

Wire Drawing Dies

Carbide dies for drawing wire.

Cold Heading Dies

Dies and die blanks for cold heading.

Punching and Stamping Dies

Carbide dies for punching and stamping.

Extrusion Dies

Dies for extruding metal profiles.

Custom Carbide Tooling

Non-standard dies made to your drawing.

Product categories

Material & Grade Selection

Carbide Grades for Dies, Molds & Metal Forming

Compare all grades →

MCG5 and MCG6 are high-toughness grades for cold heading die blanks and metal forming tools. For screw forming dies, MCA18 suits die openings below 20 mm and MCA24 openings from 20 to 50 mm; MCT15 and MCT20 are for stainless steel screws, with die openings below and above 2 mm. MCA20 is used for warm and hot forging dies, and YG20 for stamping dies, battery case forming dies and screw forming tools.

Tungsten carbide grades for Dies, Molds & Metal Forming with typical properties
GradeISOCo (%)Grain Size (μm)Density (g/cm³)Hardness (HRA)TRS (N/mm²)Application
YG20G40201.513.6852500Impact-resistant tungsten carbide grade for stamping dies, battery case forming dies, screw forming tools and cold heading dies requiring high toughness.
MCG5—12Medium14.388.33300High-toughness cemented carbide grade for cold heading die blanks and metal forming tools.
MCG6—14Medium14.1287.33140High-toughness tungsten carbide grade for cold heading dies and demanding metal forming applications.
MCA18—18Coarse13.7585.12940Tungsten carbide grade for screw forming dies with die openings below 20 mm in diameter.
MCA24—24Coarse13.2582.52650Tungsten carbide grade for screw forming dies with die openings from 20 to 50 mm in diameter.
MCT15—15Coarse13.8862700Tungsten carbide die grade for cold forming stainless steel screws with die openings below 2 mm in diameter.
MCT20—20Coarse13.684.52660Tungsten carbide die grade for forming stainless steel screws with die openings above 2 mm in diameter.
MCA20—20Coarse13.5584.12740Tungsten carbide grade for warm forging and hot forging die applications.

Technical FAQ

Dies, Molds & Metal Forming: Technical FAQ

Which grade is used for screw forming dies?

It depends on the die opening: MCA18 below 20 mm and MCA24 from 20 to 50 mm. For stainless steel screws, MCT15 is used below 2 mm and MCT20 above 2 mm.

Which grade suits warm or hot forging dies?

MCA20 is our grade for warm forging and hot forging die applications.

Do you make dies to customer drawings?

Yes. Send the die drawing, the workpiece material and the quantity; our engineers confirm feasibility, grade and tolerance before quotation.

What should I send for a quotation?

The die type and drawing, the workpiece material and size, the forming method, and the quantity.

Request a Quote

Send Your Drawing and Operating Conditions

Our engineers review the drawing and the application, recommend a grade and reply with questions or a quotation.

For a faster quotation, include:

  • Drawing (PDF) or main dimensions
  • Operating conditions: media, loads, temperature
  • How the current part wears or fails
  • Quantity and delivery schedule

Inquiry about: Dies, Molds & Metal Forming

Files are used only to process your inquiry. Do not include confidential data unless you agree to share it with MOSCARB. Privacy policy