Oil & Gas Industry

Tungsten Carbide for Oil and Gas Applications

Drilling fluids, produced sand and high-velocity flow wear out steel parts quickly. MOSCARB makes tungsten carbide bit nozzles, sleeves for electric submersible pumps, valve discs, choke trim and wear parts for MWD, LWD and stabilizer tools, in grades chosen for erosion, impact and corrosion.

Wear challenge
Fluid Erosion
Wear challenge
Abrasion by Sand and Solids
Wear challenge
Wear with Corrosion
Wear challenge
Impact and Pressure
Offshore oil and gas platform

Industry Overview

Oil & Gas Industry Overview

Oil and gas equipment works in some of the hardest wear conditions in industry: abrasive drilling mud pumped through bit nozzles, sand carried in produced fluids, and high-velocity flow through chokes and valves. Parts in these positions wear by erosion and abrasion, often combined with corrosion and impact.

Tungsten carbide is used where steel parts do not last. MOSCARB supplies carbide nozzles for PDC and roller cone bits, sleeves and bushings for electric submersible pumps, valve discs and choke valve trim, and wear parts for MWD and LWD systems and drilling stabilizers. Parts are made to customer drawings in grades selected for the service.

Typical Applications

Oil & Gas Industry Applications

01

PDC and Roller Cone Bits

Threaded nozzles for PDC bits and non-threaded sleeve nozzles for roller cone bits direct drilling fluid to the bit face.

02

Electric Submersible Pumps

Carbide sleeves and bushings for ESP pumps running in sand-laden well fluids.

03

Flow Control

Valve discs and choke valve trim that control flow in production and drilling systems.

04

MWD, LWD and Stabilizers

Wear parts for measurement-while-drilling and logging-while-drilling tools and for drilling stabilizers.

Operating Conditions

Operating Conditions & Wear Challenges

Operating conditions

  • High-velocity fluid erosion
  • Abrasive particles: drilling mud solids and produced sand
  • High-pressure operating conditions
  • Combined wear and corrosion

Fluid Erosion

Jets and choked flow drive particles at high speed onto nozzle bores and trim surfaces; a hard, fine-grained grade and a smooth flow path resist the loss of material.

Abrasion by Sand and Solids

Sand and cuttings wear sliding and rotating surfaces such as sleeves and bushings; hardness is the main defence.

Wear with Corrosion

Corrosive well fluids can attack the cobalt binder and speed up wear, so the binder is reviewed against the fluid.

Impact and Pressure

Downhole tools see shock and high contact pressure; tougher grades are used where chipping is the risk.

Carbide Solutions

Recommended Carbide Components

Tungsten carbide components we make for Oil & Gas Industry.

Bit Nozzles

Threaded nozzles for PDC bits and non-threaded sleeve nozzles for roller cone bits.

ESP Sleeves and Bushings

ESP sleeves, straight sleeves and wear sleeves for electric submersible pumps.

Valve Discs

Tungsten carbide valve discs for oil and gas applications.

Choke Valve Trim

Carbide trim components for choke valves.

MWD / LWD Components

Tungsten carbide components for LWD and MWD systems.

Stabilizer Wear Parts

Wear parts for drilling stabilizers, and custom wear parts to drawing.

Product categories

Material & Grade Selection

Carbide Grades for Oil & Gas Industry

Compare all grades →

Our oil and gas grades range from impact resistance to high hardness: MS50H for sleeves, bushings and wear parts that see impact as well as wear; MS30H for precision sleeves and bushings; MSGU10 where hardness and wear resistance come first; and MSGK05A for oil-immersed pump components, needle valve tips and valve seats.

Tungsten carbide grades for Oil & Gas Industry with typical properties
GradeISOCo (%)Grain Size (μm)Density (g/cm³)Hardness (HRA)TRS (N/mm²)Application
MS50HG30141.5-3.013.95-14.1588.2-89.23800Impact-resistant and wear-resistant tungsten carbide grade for shaft sleeves, bushings and custom wear parts used in oil and gas and chemical processing equipment.
MS30HK3081.5-3.014.7590.22800Tungsten carbide grade with a balance of wear resistance and toughness for precision shaft sleeves and carbide bushings.
MSGU10K05-K1060.6-0.914.85933000High-hardness, wear-resistant tungsten carbide grade for shaft sleeves and bushings in demanding industrial equipment.
MSGK05AK10-K2061.0-2.014.95923200Wear-resistant, high-toughness tungsten carbide grade for oil-immersed pump components, needle valve tips and valve seats.

Technical FAQ

Oil & Gas Industry: Technical FAQ

Which tungsten carbide grade is used for ESP sleeves and bushings?

MS30H balances wear resistance and toughness for precision shaft sleeves and bushings. MS50H is used where impact is also expected, and MSGU10 where high hardness is needed. The grade is confirmed against your operating conditions.

Do you make nozzles for PDC and roller cone bits?

Yes. We make threaded tungsten carbide nozzles for PDC bits and non-threaded sleeve nozzles for roller cone bits. Send the thread specification and nozzle dimensions or a drawing.

Can carbide parts be used in corrosive well fluids?

Corrosive fluids can attack the cobalt binder of standard grades. Tell us the fluid, pH and temperature so our engineers can review the grade before quotation.

What information do you need for a quotation?

A drawing, the operating conditions (fluid, sand content, pressure, temperature), how the current part wears, and the quantity.

Request a Quote

Send Your Drawing and Operating Conditions

Our engineers review the drawing and the application, recommend a grade and reply with questions or a quotation.

For a faster quotation, include:

  • Drawing (PDF) or main dimensions
  • Operating conditions: media, loads, temperature
  • How the current part wears or fails
  • Quantity and delivery schedule

Inquiry about: Oil & Gas Industry

Files are used only to process your inquiry. Do not include confidential data unless you agree to share it with MOSCARB. Privacy policy