Industrial Wear Protection

Tungsten Carbide Industrial Wear Parts

Where equipment surfaces are scoured by abrasive material, tungsten carbide wear parts protect them. MOSCARB supplies carbide wear plates, wear and step strips, perforated special-shaped plates and custom wear parts in YG grades, chosen for how much wear and impact each part sees.

Wear challenge
Abrasive Wear
Wear challenge
Particle Erosion
Wear challenge
Sliding Friction
Wear challenge
Impact
Rolling mill rolls for industrial wear applications

Industry Overview

Industrial Wear Protection Overview

Equipment surfaces wear when abrasive material slides along or strikes against them. Replacing the worn surface with tungsten carbide plates, strips or custom parts protects the equipment where steel wears too fast.

MOSCARB supplies blank, precision and mirror-finished plates, wear strips, step strips, special-shaped perforated plates and custom wear parts made to drawing, in YG grades selected for wear and impact.

Typical Applications

Industrial Wear Protection Applications

01

Wear Plates

Carbide plates for surfaces exposed to abrasive wear.

02

Wear Strips

YG8 wear strips and YG6 impact-resistant strips for edges and sliding surfaces.

03

Refractory Brick Molds

YG11 plates for molds used to press refractory bricks.

04

Custom Wear Components

Parts made to drawing in YG grades for wear and impact.

Operating Conditions

Operating Conditions & Wear Challenges

Operating conditions

  • Abrasive wear
  • Particle erosion
  • Sliding friction
  • Severe wear environments

Abrasive Wear

Hard particles slide across the surface and cut material away; harder grades wear more slowly.

Particle Erosion

Particles striking the surface erode it; the angle and speed of impact decide whether hardness or toughness matters more.

Sliding Friction

Material sliding along strips and plates wears them steadily; flatness and fixing matter as well as the grade.

Impact

Lumps and heavy loads can chip carbide; the tougher YG15 and YG20 are used where impact is high.

Carbide Solutions

Recommended Carbide Components

Tungsten carbide components we make for Industrial Wear Protection.

Wear Plates

Blank, precision and mirror-finished carbide plates.

Wear Strips

Wear strips, step strips and impact-resistant strips.

Perforated and Shaped Plates

Special-shaped plates with holes, made to drawing.

Custom Wear Parts

Non-standard wear parts in YG grades.

Product categories

Material & Grade Selection

Carbide Grades for Industrial Wear Protection

Compare all grades →

YG6 and YG8 are used for wear-resistant parts under moderate loads, such as wear plates, nozzles and saw tips. YG15 is tougher, for components under heavy loads and impact, and YG20 is our impact-resistant grade for stamping and forming dies.

Tungsten carbide grades for Industrial Wear Protection with typical properties
GradeISOCo (%)Grain Size (μm)Density (g/cm³)Hardness (HRA)TRS (N/mm²)Application
YG6K1061.515.592.52720Tungsten carbide grade for wear-resistant saw tips, nozzles and custom carbide components subjected to mechanical loads.
YG8K2081.514.7902900Wear-resistant tungsten carbide grade with high strength for custom carbide wear parts, saw tips, wear plates and components operating under moderate mechanical loads.
YG15K40151.514.05872700Tough tungsten carbide grade for custom wear-resistant components subjected to heavy mechanical loads and impact.
YG20G40201.513.6852500Impact-resistant tungsten carbide grade for stamping dies, battery case forming dies, screw forming tools and cold heading dies requiring high toughness.

Technical FAQ

Industrial Wear Protection: Technical FAQ

Which grade should I use for wear plates?

YG6 has the higher hardness (92.5 HRA typical) and YG8 the higher strength (TRS 2900 N/mm² typical), so YG6 suits pure abrasion and YG8 parts that also carry load. Where impact is heavy, YG15 or YG20 is used.

Can you make perforated or special-shaped carbide plates?

Yes. Send a drawing with the outline and hole positions; our engineers confirm feasibility, grade and tolerance before quotation.

Do you supply mirror-finished plates?

Yes. Mirror-finished tungsten carbide plates are part of our range, as well as blank and precision plates.

What should I send for a quotation?

A drawing, the material the part is exposed to, the type of wear and impact, the grade if known, and the quantity.

Request a Quote

Send Your Drawing and Operating Conditions

Our engineers review the drawing and the application, recommend a grade and reply with questions or a quotation.

For a faster quotation, include:

  • Drawing (PDF) or main dimensions
  • Operating conditions: media, loads, temperature
  • How the current part wears or fails
  • Quantity and delivery schedule

Inquiry about: Industrial Wear Protection

Files are used only to process your inquiry. Do not include confidential data unless you agree to share it with MOSCARB. Privacy policy