Pumps, Valves & Fluid Control

Tungsten Carbide Components for Pumps and Valves

Pumps and valves that handle sand, slurry or corrosive fluids wear at their sliding and sealing surfaces. MOSCARB makes tungsten carbide shaft sleeves and bushings, sleeves for submersible pumps, valve discs, valve seats and choke trim, in grades chosen for sliding wear, erosion and the fluid handled.

Wear challenge
Sliding Wear
Wear challenge
Fluid Erosion
Wear challenge
Corrosive Media
Wear challenge
Continuous Operation
Industrial pumps and valves

Industry Overview

Pumps, Valves & Fluid Control Overview

In pumps, shaft sleeves and bushings run against each other for as long as the pump runs, often in fluid that carries abrasive particles. In valves and chokes, seats, discs and trim face the full velocity of the flow as they open and close. Both are typical positions for tungsten carbide.

MOSCARB supplies shaft sleeves and bushings, including sleeves for electric submersible pumps, valve discs, valve seats and needle valve tips, and choke valve trim. Grades are selected for sliding wear, erosion and the fluid handled.

Typical Applications

Pumps, Valves & Fluid Control Applications

01

Pump Shaft Sleeves and Bushings

Sliding bearing surfaces in pumps that handle abrasive or corrosive fluids.

02

Electric Submersible Pumps

ESP sleeves, straight sleeves and wear sleeves.

03

Valve Seats and Discs

Sealing surfaces that must resist erosion and wear, including needle valve tips.

04

Choke Valves

Carbide trim components for choke valves.

Operating Conditions

Operating Conditions & Wear Challenges

Operating conditions

  • Sliding wear
  • Fluid erosion
  • Corrosive media
  • Continuous operation

Sliding Wear

Sleeves and bushings run against each other, and particles in the fluid between them cause abrasive wear.

Fluid Erosion

Flow through a valve seat is fastest just as the valve opens or closes, which erodes the sealing surfaces.

Corrosive Media

Corrosive fluids can attack the binder, so the grade is reviewed against the fluid.

Continuous Operation

Pumps that run continuously need parts with steady wear behaviour and stable dimensions.

Carbide Solutions

Recommended Carbide Components

Tungsten carbide components we make for Pumps, Valves & Fluid Control.

Shaft Sleeves

Precision carbide shaft sleeves.

Bushings

Carbide bushings for pumps and rotating equipment.

ESP Sleeves

Sleeves for electric submersible pumps.

Valve Seats and Needle Valve Tips

Carbide valve seats and needle valve tips.

Valve Discs and Choke Trim

Valve discs and choke valve trim components.

Product categories

Material & Grade Selection

Carbide Grades for Pumps, Valves & Fluid Control

Compare all grades →

MS30H balances wear resistance and toughness for precision shaft sleeves and bushings. MSGU10 is a high-hardness grade for sleeves and bushings in demanding equipment. MSGK05A is used for oil-immersed pump components, needle valve tips and valve seats, and MS50H where impact and wear are combined.

Tungsten carbide grades for Pumps, Valves & Fluid Control with typical properties
GradeISOCo (%)Grain Size (μm)Density (g/cm³)Hardness (HRA)TRS (N/mm²)Application
MS50HG30141.5-3.013.95-14.1588.2-89.23800Impact-resistant and wear-resistant tungsten carbide grade for shaft sleeves, bushings and custom wear parts used in oil and gas and chemical processing equipment.
MS30HK3081.5-3.014.7590.22800Tungsten carbide grade with a balance of wear resistance and toughness for precision shaft sleeves and carbide bushings.
MSGU10K05-K1060.6-0.914.85933000High-hardness, wear-resistant tungsten carbide grade for shaft sleeves and bushings in demanding industrial equipment.
MSGK05AK10-K2061.0-2.014.95923200Wear-resistant, high-toughness tungsten carbide grade for oil-immersed pump components, needle valve tips and valve seats.

Technical FAQ

Pumps, Valves & Fluid Control: Technical FAQ

Which carbide grade suits pump shaft sleeves and bushings?

MS30H for precision sleeves and bushings where wear resistance and toughness both matter, MSGU10 where hardness comes first, and MS50H where impact is expected.

Do you make carbide valve seats?

Yes. MSGK05A is our grade for valve seats, needle valve tips and oil-immersed pump components. Send the seat drawing and the fluid.

Can you supply sleeves for electric submersible pumps?

Yes: ESP sleeves, straight sleeves and wear sleeves made to your drawing.

What should I send for a quotation?

The drawing, the fluid and its solids content, pressure and temperature, the mating part, and the quantity.

Request a Quote

Send Your Drawing and Operating Conditions

Our engineers review the drawing and the application, recommend a grade and reply with questions or a quotation.

For a faster quotation, include:

  • Drawing (PDF) or main dimensions
  • Operating conditions: media, loads, temperature
  • How the current part wears or fails
  • Quantity and delivery schedule

Inquiry about: Pumps, Valves & Fluid Control

Files are used only to process your inquiry. Do not include confidential data unless you agree to share it with MOSCARB. Privacy policy